Wireless robot BUBLUE A10 PS

Product detailed description

Pool cleaning robot Bublue A10 PS
The Bublue A10 PS is an advanced pool cleaning robot designed to remove debris from the bottom and work close to the walls - without the need for manual intervention. Thanks to its high power (33 W), it effectively removes sand, leaves and small debris in one cycle. It works without a cord for up to 90 minutes, and thanks to fast charging, it's ready for the next cycle after just about 3 hours. The DirtLock™ Tech 2.0 system effectively traps debris in the filter basket, and smart wall detection makes it easy to reposition. In addition, the auto-parking function allows the robot to be conveniently removed when the job is done. The entire device is complemented by LEDs that indicate the status of the device.

Bluehole Technology™ - efficiency visible after one cycle
The high cleaning efficiency is the result of the new Bluehole Technology™, which improves the cooperation between nozzle, motor and suction rotor. This translates into up to twice the overall performance compared to previous solutions, as well as 3× higher efficiency in leaf collection and 8.5× higher efficiency in removing debris from 3 to 8 mm (compared to the previous generation). As a result, a single cleaning cycle is all it takes to restore cleanliness without the need for hand vacuuming or restarting the machine.

Intelligent sensors, autonomous parking and bright LED signals
The Bublue A10 PS Robotic Pool Cleaner has been designed with maximum user comfort in mind, so it uses advanced contact sensors that enable a fast and accurate response to the pool walls. Corner Boost™ technology increases cleaning intensity in corners and offers up to twice the cleaning efficiency to remove debris in these critical areas. When the robot hits an edge, it automatically corrects its path and moves smoothly and without chaotic bouncing, resulting in smoother and more efficient bottom cleaning. At the end of the cycle, the device parks itself against the pool wall, allowing it to be quickly and conveniently removed from the water. In addition, built-in LEDs provide real-time information on the operating status, charge level and readiness of the device.

Dual filtration and DirtLock™
The dual filtration system combines two levels of 80 and 150 mesh sieves that effectively trap larger debris such as leaves as well as fine sand or sediment. This solution increases the average vacuuming efficiency by up to 15% and keeps the water cleaner throughout the cycle. It is complemented by DirtLock™ technology, which allows the water to be quickly drained from the robot in approximately 5 seconds, reducing maintenance time by up to 80% and preventing nearly 100% backflow of trapped debris into the pool. In addition, the optimized basket design provides up to 30% more capacity compared to standard solutions, which means longer operation without the need for frequent emptying.

Precise interplay of components - stable suction performance throughout the entire operating cycle
The Bublue A10 PS is equipped with an optimised suction system in which nozzle, motor and impeller work in perfect synchronisation. This design allows a smooth flow of water and dirt throughout the system without loss of power or sudden drop in performance. The precise alignment of these components results in a stable and efficient suction of small particles and larger debris, regardless of the degree of contamination of the pool bottom. The result is consistent robot operation, better energy utilization and consistently high cleaning efficiency from start to finish.

Long run time and fast charging - ready to clean whenever you need it
The robot is equipped with a 4400 mAh battery that provides up to 90 minutes of continuous operation, allowing for a thorough cleaning of the pool bottom in one cycle. After cleaning, the device recharges in approximately 3 hours, so it quickly returns to full readiness and does not require long breaks between uses. This combination of operating time and charging time makes the Bublue A10 PS the ideal choice for above-ground pools up to approximately 80 m² with a flat bottom.

Easy maintenance - clean the robot without tools and effort
When the work is finished, simply rinse the filter and the robot housing with a normal garden hose - there is no need to disassemble the device or use additional accessories. This form of cleaning makes it easy to remove sand, leaves and small debris.

Technical parameters:

Rated power: 33 W
Operating time: 90 minutes
Charger input voltage: 100-240 V
Charger output voltage: 12.6 V DC
Charger output current: 1.8 A
Battery capacity: 4400 mAh
Charging Time: Approximately 3 hours
Supported pool area: 80 m²
Filter density: 180 μm
Weight: 3.5 kg
Cleaning depth: 3 m
Waterproof rating: IPX8

Contents of the package:

Cleaning robot for swimming pools
Charger
Hook to pull the robot out of the water
Handle
Brush x2
Instructions for use