Epever XTRA1210N solar MPPT controller, 12/24V, 10A, 100V input
Code: ABCT_A500002650Product detailed description
MPPT solar controller EPEVER XTRA - new generation of solar controllers brings high quality and maximum equipment for island systems with panel voltage up to 100 V and maximum charging current 10 A. Battery 12/24V, PV max130/260Wp.
This solar controller is suitable for a wide range of island applications such as cottages, houses, etc.
It is also suitable for use in vehicles thanks to the possibility of earthing to the minus pole.
A multifunction display is integrated directly in the MPPT controller for easy monitoring of the system and possible adjustment of operating parameters, including control LEDs.
The regulator works as an inverter, that is, it can process higher input voltage and lower current to lower voltage/increase current with high efficiency. So we can use almost any solar panel. The controller is compatible with lead acid and lithium ion batteries.
The solar controller is equipped with the latest MPPT (Maximum Power Point Tracking) technology - maximum power point tracking with a sophisticated tracking algorithm where the solar module operates at the ideal voltage that the solar module can produce at the highest available power. When compared to a conventional PWM controller, MPPT technology increases charging efficiency by about 30%.
The maximum charging power to the battery of this model is 10A which corresponds to a panel power of 130 Wp if you have a 12V battery, or 260 Wp if you have a 24V battery. In case the panel will give higher power, then the controller will only limit it to its nominal max power. The power of the PV panels must not be higher than 1.5 times the nominal power of the controller!
The maximum charging power to the battery of this model is 10A which corresponds to a panel power of 130 Wp if you have a 12V battery, or 260 Wp if you have a 24V battery. In case the panel will give higher power, then the controller will only limit it to its nominal max power. The power of the PV panels must not be higher than 1.5 times the nominal power of the controller!
You can connect solar panels in series, but their output voltage at empty, referred to as Voc, must never exceed the value of the empty voltage Voc 100V - exceeding this value will permanently damage the regulator (here it is necessary to take into account that the voltage of the solar panel increases with decreasing ambient temperature and the value of Voc specified in the parameters of the solar panel is at 25C. Therefore, we do not recommend that the value of the stated Voc exceeds 90V)
Setting the controller parameters (mainly the type of battery used) is done using the built-in LCD of the XDS2, ormT50 external display - not included in the controller.
Parameter setting and monitoring can also be done on your PC - you will only needEPsolar USB communication cable and software, which you can download for free in the related documents. It can also be monitored and set up using a mobile phone/tablet. For this you will needbluetooth module BLE-01.
The manufacturer EPsolar is today practically the largest manufacturer of solar controllers and after more than eight years of our own experience with its products we will recommend this model as a highly reliable and quality product at a reasonable price.
Quick installation:
1. We connect a battery to the solar controller. Install a suitably sized DC fuse on the plus wire as close to the battery pole as possible (position 3)
2. Connect the load (position 4)
3. Connect solar panel (position 2)
(position 1) - possibility to connect an external temperature sensor
(position 5) - possibility to connect external display MT-50, USB communication cable for communication with PC or Bluetooth module BLE-01 for communication with mobile phone/tablet
Basic features:
- Multifunctional built-in LCD display of XDS2 design for complete monitoring and parameter setting
- High degree of protection IP32
- Plate front cover, rear part made of extruded aluminium - heat sink
- The communication port uses a professional protection chip which can provide 5VDC power supply and has over-current and short circuit protection.
- Advanced MPPT technology with at least 99.5% efficiency
- Very high tracking speed and guaranteed tracking efficiency
- Advanced MPPT control algorithm to minimize lost rate and lost time
- High quality components, improving system performance with a maximum conversion efficiency of 98%
- Accurate detection and monitoring of the maximum power point
- Automatic limitation of charging power and current
- Wide MPP operating voltage range
- Compatible with lead acid and lithium ion batteries
- Battery temperature compensation function
- Real-time operational statistics function
- Temperature reduction function for overheating
- With RS-485 communication bus interface and Modbus communication protocol, it is available to meet various requirements
- Monitor and set parameters using your mobile phone or PC
- Extensive electronic protection
Overview of protections:
- PV overcurrent
- Short circuit PV
- Reverse PV polarity
- Reverse battery polarity
- Battery overvoltage
- Excessive battery discharge
- Battery overheating
- Low temperature lithium battery
- Load short circuit
- Load overload
- Overheating of the controller
Further technical parameters can be found in the related documents.
Additional parameters
| Category: | ABC Tech |
|---|---|
| Weight: | 0.57 kg |
| EAN: | 6974241250484 |
| EAN: | 6974241250484 |
Be the first who will post an article to this item!
Add a comment