PRESS wall - end - 1/2 "Fx16 IVAR.MP 5760

Product detailed description

Press end fittings are essential components in modern heating and plumbing systems, particularly in applications where high reliability and resistance to thermal stress are required. This type of fitting is commonly used in residential and commercial buildings, including underfloor heating systems, central heating circuits, and hot water distribution. The IVAR.MP 5760 model is designed for use in environments where the system operates at nominal pressure PN 10 and temperatures up to 120°C. It is intended for use with ALPEX and TURATEC cross-linked polyethylene (PE-X) pipes, which are known for their flexibility and durability in hot water applications.

The fitting is installed using a press tool that compresses the sleeve and sealing ring around the pipe, creating a leak-tight connection. This method eliminates the need for threading or soldering, reducing installation time and the risk of human error. The fitting is suitable for both new installations and system repairs, and its robust design ensures long-term performance in demanding environments.

Technical parameters

Material	Brass CW617N
Operating temperature	+120 °C
Nominal pressure	PN 10
Code	513001MPHD
Brand	IVAR

The nominal pressure rating of PN 10 and the maximum operating temperature of +120°C are critical for determining the suitability of this fitting in specific applications. These parameters ensure the fitting can handle typical domestic hot water and heating system conditions. The material selection—brass CW617N for the body and stainless steel for the sleeve—provides resistance to corrosion and mechanical stress, making it ideal for use in closed-loop systems and long-term installations.

Installation and connection

To install the IVAR.MP 5760 press end fitting, the installer must first prepare the pipe by cutting it cleanly and deburring the end. The pipe is then inserted into the fitting until it reaches the stop mark. A press tool is used to compress the sleeve and sealing ring around the pipe, ensuring a secure and leak-free connection. The fitting is available with a 1/2 inch female thread (F) and a 16 mm diameter for the pipe. It is important to verify that the pipe is correctly inserted to the stop mark and that the press tool is properly aligned to avoid misalignment or damage to the fitting. Common installation errors include over-pressing, which can deform the fitting, and under-pressing, which can result in a weak connection.

Compatibility and accessories

This press end fitting is specifically designed for use with ALPEX and TURATEC PE-X pipes. It is compatible with standard press tools used in the industry. For a complete installation, the following accessories may be required: press tools, pipe cutters, deburring tools, and sealing rings. No related products are listed for this model.

Technical background for designers

The IVAR.MP 5760 press end fitting operates on the principle of mechanical compression, where the sleeve is pressed around the pipe to form a tight seal. The brass body provides structural strength and resistance to thermal expansion, while the EPDM sealing ring ensures a watertight connection. The stainless steel sleeve adds durability and resistance to mechanical wear. The fitting is integrated into the system by connecting it to the pipe and securing it with a press tool. The service life of the fitting is influenced by factors such as installation quality, operating pressure, and temperature fluctuations. Proper installation and adherence to manufacturer guidelines are essential for optimal performance.

Service and operation

This press end fitting requires minimal maintenance due to its robust design and sealed connection. No regular service intervals are specified in the technical documentation. However, it is recommended to inspect the fitting periodically for signs of wear, corrosion, or leakage. If any issues are detected, the fitting should be replaced to maintain system integrity. The fitting is designed for long-term use and does not require routine maintenance under normal operating conditions.

Frequently asked questions

Can the IVAR.MP 5760 be used with copper pipes?
No, this fitting is specifically designed for use with ALPEX and TURATEC PE-X pipes. Using it with copper pipes would not be compatible and could result in a failed connection.

Is the fitting suitable for use in hot water systems?
Yes, the fitting is rated for operating temperatures up to 120°C, making it suitable for hot water systems and heating applications.

Can the fitting be used in a pressurised system?
Yes, the fitting is rated for nominal pressure PN 10, which is suitable for most domestic and commercial hot water and heating systems.

Is the fitting compatible with standard press tools?
Yes, the IVAR.MP 5760 is designed to be used with standard press tools commonly used in the industry for PE-X pipe installations.